Produse pentru aramex intl (4)

Osmocem SCK Fiber-reinforced monocomponent cement mortar, based on hydraulic binders, superprogoline fillers, selected fine aggregates and crystallizing reagent agents, which favor the penetration of the compound into the support. Ideal for low-thickness protective coatings (4 to 10 mm), with high counterweight adhesion. The specific formulation makes this product ideal for coatings in aggressive environments in contact with chlorides and sulphates (sewage systems). Packaging: 25 kg bag UM: €/kg

Protech Fix AC-Therm Water-based anti-condensing wall covering, with excellent fixing and anchoring properties, with good coverage based on high penetration acrylic resins, 3M Glass Bubble, pigments, fillers and covering fillers. Suitable as an anti-condensation fixative primer, prior to painting or coating the plaster with anti-condensation paints or plasters (-THERM). Ideal for interventions on walls with mucilage deposits, bacterial phenomena and moulds. Due to its low thermal conductivity, it is particularly suitable for solving mould problems. It can be applied on any plaster (rustic, civil, plaster, dry mortar, plasterboard, concrete, prefabricated, exposed concrete, etc.). Made with special resins and additives it reduces the absorption of the support while allowing the necessary transpiration, uniforms the absorption making the application of the finishing coats easier. It always works in depth, which is why it is the ideal preparation for applying water-based paints or coatings. Adhesion is excellent even on particularly difficult surfaces, thanks to the use of special resins and the presence in the formulation of an adhesion promoter interacting between the support and the product. Preliminary treatment of any surface (civil, plaster, rustic, dry mortars, plasterboard, concrete, prefabricated, exposed concrete etc.) designed to isolate the support surfaces and standardise the absorptions of the subsequent anti-condensate treatments (painting and protective coatings). Packaging: 14-liter bucket UM: €/l

Anchorsana Fix Premixed based on hydraulic lime, special sulfur aluminate binders, water retainers, shrinkage compensators and reducers of the water/binder ratio, used for fixing and anchoring, in masonry, connectors, inserts, bars, brackets, grouting of the joints, tacking of lesions. It is a product with accelerated setting and hardening, with setting start at 30 ', end setting at 60' and development of mechanical strength already after 90 'of curing. Particularly recommended in the restoration of period and monumental buildings. The particularly fine constituent materials allow adequate anchoring even in the presence of a small space between hole and connectors. By mixing Anchorsana Fix with different water contents, the product passes from thixotropic consistencies (23% water) to fluid gel consistencies (30% water), allowing any type of anchoring, from overhead to inclinations towards the bass. The product does not contain resins and solvents and can also be used indoors, subject to the usual precautions necessary when handling materials based on alkaline and irritating powders such as lime (use suitable personal protective equipment, such as gloves and protective goggles). Fixing and anchoring, in masonry bodies, of rigid connectors, jib connectors, inserts, bars with improved adherence, anchors. It develops great adhesion on materials of different nature: metal, fiberglass, basalt. Blow with compressed air and forced suction of the housing holes. The application surfaces must be clean, free of dirt, moving, crumbly and incoherent parts, dust, etc., suitably saturated with water until reaching the condition of "saturated with dry surface". Pour about 2/3 of the mixing water into the mixer; gradually add Anchorsana Fix and the water still required, continuing to mix, until a homogeneous, lump-free mixture of the desired consistency is obtained. Apply with a trowel or by casting. The mixing water indicatively required is equal to 23% by weight for thixotropic doughs, and to 30% by weight for doughs with a plastic-fluid consistency. Approximately 1.6 kg of Anchorsana Fix for each cubic decimeter of volume to be filled. Bag 25 kg - Pallet: 50 x (Bag 25 kg)

Osmocem N gray Cement compound for the preparation, with the sole addition of water, of a waterproofing osmotic coating that can create horizontal and vertical barriers, also suitable in conditions of negative hydrostatic thrust vis-à-vis water permeation in the buildings. Typical uses include waterproofing underground rooms, elevator compartments, garages, basements, tanks, etc. The action of the active components and of the adhesion promoters of Osmocem N, saturated by the reaction the support capillaries, forming a complex system of gel and stable crystals, which results in the best sealing, effective even in conditions of negative hydrostatic thrust, without hindering the breathability of the walls. Osmocem N is compatible for food substances: is certified as suitable for the containment of foodstuffs and drinking water (Certificate no. 02/2010 Laboratorio Analysis Service di Settimo di Pescantina - VR). Osmocem N waterproof test: • Resistance to positive hydraulic thrust, UNI EN 12390/8: water penetration depth with 5 bar pressure = 1-2 mm (*) • Impermeability to negative hydraulic thrust, UNI EN 12390/8 modified (concrete support a / c ratio 0.7): no passage of water with a pressure of 1.5 bar (*) concrete with penetration depth <= 20 mm are considered waterproof. Waterproofing rigid structures and masonry walls underground, buried or in any case subject to water permeation: lift wells, basements, tanks, pipes, tunnels, garages, bridges, reservoirs, areas containing food, etc. in conditions of positive and negative hydrostatic thrust provided they are sufficiently porous and absorbent and free from any waterproofing and / or water-repellent surface treatment, whether chemical (siloxanes, epoxies, polyurethanes, etc.) or natural (wax-up). Application surfaces should be clean, free of soiling, crumbling and non-adhering parts, dust, etc., water repellent treatments in general, etc. conveniently saturated with water until they reach the condition "saturated with dry surface". Pour about 2/3 of the mixing water into the mixer, add Osmocem N and the remaining water; continue to mix until a homogeneous lump-free mixture is obtained. The mixing water should be about 19-20% (for interventions in the form of a spatula) or 21-22% (for interventions using a brush with long bristles). After mixing is completed wait a few minutes before applying. If applied by brush, roll out two or more crossed coats. Although it is not a specific product for finishing thick coats, it can still be used for these purposes. In these cases, it is appropriate to use a fibreglass mesh Armaglass 160. Approximately 1.7 kg/m² of Osmocem N for each millimetre of thickness to be made. Packaging: 25 kg bag UM: €/kg